HONDA finally began offering a hydraulic clutch beginning on the 2021 HONDA CRF 450R. And for some unknown reason, the line routing is right in your face! It just feels wrong! Plus it's a cheap rubber line that allows some squishiness in the lever feel.  

Get a nice consistent solid feel with our stainless steel braided line upgrade that also reroutes the line behind the number plate, just like on Ken Roczens bike!  

Please note, the line shown in the images here has transparent red end fittings, but all of our production lines have polished stainless as shown in the line photo below. 

Trick Lightweight drilled WORKS style aluminum washers available in 25mm OD and and 18mm OD for use with M6 bolts.

• M25 is 25mm (about 1") OD and is the size shown in the pictures.
• M18 is 18mm OD (about 5/8") and is commonly used on 2 strokes for pipe mounts etc.

Most popular application is on the upper and lower radiator mounts and on the gas tank mounting bolt as shown in the above images.

SOLD individually so please order accordingly!

CLOSEOUT!

Pair of Billet Aluminum Banjo Bolts with Safety Wire holes (a new set of copper seals included with each kit)

M10 X 1.25 fits all Japanese MX bikes. (does not fit KTM/HUSKY) 20mm long from the base of the bolt flange to the tip of the threads Sold by the pair (1 pair is 2 bolts), so please be sure to select the quantity you want in the shopping cart before checking out! Our new design fits all JAPANESE MX bikes 2004-2020 and features a small 12mm head so there are no clearance issues at the rear master cylinder! And they are also now drilled for safety wire. At only $18 each, these are half the price of similar high-end banjo bolts on the market!

Torque to 12-14 lbs/ft!

CLOSEOUT!

Upgrade the appearance, performance, and reliability of your bike by switching out its stock rubber hoses with MOTO STUFF Silicone Radiator Hose Kit. The kit features premium-grade silicone throughout providing increased temperature and pressure performance. This is especially important if you are running a high compression piston or higher pressure radiator caps.

Features Include: Made of premium-grade silicone Operates at higher temperatures and pressures than stock rubber hoses Features a premium red or blue silicone pigment that will stay vibrant and will not fade over time like economy hose kits.

The kit features premium-grade silicone throughout providing increased temperature and pressure performance. Features Include: Made of premium-grade silicone Operates at higher temperatures and pressures than stock rubber hoses Features a premium red or blue silicone pigment that will stay vibrant and will not fade over time like economy hose kits.

Features Include: Made of premium-grade silicone Operates at higher temperatures and pressures than stock rubber hoses Features a premium red or blue silicone pigment that will stay vibrant and will not fade over time like economy hose kits.

Made of premium-grade silicone: Provides greater protection when operating at higher temperatures and pressures than stock rubber hoses Features a premium red or blue silicone pigment that will stay vibrant and will not fade over time like economy hose kits.

CLOSEOUT! 

Honda introduced a plastic radiator plug on the left radiator of the 2014 CRF 250R and the 2013-20140 CRF 450R to allow air to be purged from the cooling system when refilling. The plug can be damaged by rock impact or melt under extreme load conditions. Coolant loss or even minimal cooling system pressure loss can lead to rapid serious engine damage with costly repairs. HONDA does not sell the stock plug separate from the radiator!

Details:

• Alloy CNC machined red anodized includes heat-resistant o-ring
• M12 X 1.25 

Fits:

• 2014-2017 CRF 250R
• 2013 - 2016 CRF 450R

Kawasaki introduced a plastic radiator plug on the left radiator of the 2016 KX 450F  to allow air to be purged from the cooling system when refilling. The plug can be damaged by rock impact or melt under extreme load conditions. Coolant loss or even minimal cooling system pressure loss can lead to rapid serious engine damage with costly repairs.  

Details:

• Alloy CNC machined red anodized includes heat-resistant o-ring

• Fits: 2016-2018 KX 450F

Splitstream Fuel Filter Honda CRF

Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.

A couple of things we noticed while testing the Splitstream fuel filters over the past few months.

1. We were concerned that the filter might slow down the filling process, but we did not experience that with any of our fuel jugs. If you do begin to experience reduced fill speed, then it's probably time to pull the filter out and give it a good wash with hot water and dish soap in the kitchen sink. Be sure to rinse thoroughly!
2. On the first fill-up, it seems like the sock filter will prevent you from being able to see the fuel level as the tank is filling, but it is just like normal, you can see the fuel level in the sock as the tank fills. Below are links to recent posts on Thumpertalk.com that go into the severity of the problem in much more detail.

Here are some helpful links regarding the fuel system on modern injected bikes:

• http://www.thumpertalk.com/topic/751249-efi-owners-bike-bogging-the-fix-with-pics/
• http://www.thumpertalk.com/topic/713577-09-crf-450-fuel-problems/
• http://www.thumpertalk.com/topic/676526-09-fuel-pump/

With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.

Initially, the complete fuel pump assembly had to be replaced at over $300 on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......

The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.

This filter fits the following Bikes:

• HONDA CRF 250R 2010-2017
• HONDA CRF 450R 2009-2016
• Does not fit 2017 -2018 450R or RX or 2018 CRF 250R

Splitstream Fuel Filter Kawasaki KX-F

Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.

A couple of things we noticed while testing the Splitstream fuel filters over the past few months.

1. We were concerned that the filter might slow down the filling process, but we did not experience that with any of our fuel jugs. If you do begin to experience reduced fill speed, then it's probably time to pull the filter out and give it a good wash with hot water and dish soap in the kitchen sink. Be sure to rinse thoroughly!
2. On the first fill-up, it seems like the sock filter will prevent you from being able to see the fuel level as the tank is filling, but it is just like normal, you can see the fuel level in the sock as the tank fills. Below are links to recent posts on Thumpertalk.com that go into the severity of the problem in much more detail.

Here are some helpful links regarding the fuel system on modern injected bikes:

• http://www.thumpertalk.com/topic/751249-efi-owners-bike-bogging-the-fix-with-pics/
• http://www.thumpertalk.com/topic/713577-09-crf-450-fuel-problems/
• http://www.thumpertalk.com/topic/676526-09-fuel-pump/

With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.

Initially, the complete fuel pump assembly had to be replaced at over $300 on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......

The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.

This filter fits the following Bikes:

• Fits 2009-2020 Kawasaki KX250F & KX450F
• Kawasaki Teryx4

Splitstream Fuel Filter HUSQVARNA & KTM

Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.

A couple of things we noticed while testing the Splitstream fuel filters over the past few months.

1. We were concerned that the filter might slow down the filling process, but we did not experience that with any of our fuel jugs. If you do begin to experience reduced fill speed, then it's probably time to pull the filter out and give it a good wash with hot water and dish soap in the kitchen sink. Be sure to rinse thoroughly!
2. On the first fill-up, it seems like the sock filter will prevent you from being able to see the fuel level as the tank is filling, but it is just like normal, you can see the fuel level in the sock as the tank fills. Below are links to recent posts on Thumpertalk.com that go into the severity of the problem in much more detail.

Here are some helpful links regarding the fuel system on modern injected bikes:

• http://www.thumpertalk.com/topic/751249-efi-owners-bike-bogging-the-fix-with-pics/
• http://www.thumpertalk.com/topic/713577-09-crf-450-fuel-problems/
• http://www.thumpertalk.com/topic/676526-09-fuel-pump/

With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.

Initially, the complete fuel pump assembly had to be replaced at over $300 on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......

The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.

Available for the following HUSQVARNA & KTM models:

• HUSQVARNA 2014-2020 TC & FC models
• HUSQVARNA 2014-2020 Enduro FE 250/350/450
• KTM 1/4 Turn cap and 2009-2012 3-tab 1/4 Turn caps
• KTM 2012 Dungey Replica with screw-in cap
• KTM 2013-2020 SXF Models with screw-in cap

CLOSEOUT!

Red anodized lightweight Banjo Bolts with holes drilled for safety wire and copper washers.

Fits all Japanse MX bikes but the following:

• Cannot be used in the front master cylinder on HONDA's.  (22mm length is too long) 
• Does not fit KTM or Husky

Sold as a pair.

CLOSEOUT!

Pair of Billet Aluminum Banjo Bolts with Safety Wire holes (a new set of copper seals included with each kit)

M10 X 1.0 fits all KTM, HUSKY and Gas Gas bikes with Brembo brakes. 19 mm long from the base of the bolt flange to the tip of the threads Sold by the pair (1 pair is 2 bolts), so please be sure to select the quantity you want in the shopping cart before checking out! Our new design fits all KTM, HUSKY and Gas Gas bikes with Brembo brakes and features a small 12mm head so there are no clearance issues at the rear master cylinder! And they are also now drilled for safety wire. At only $18 each, these are half the price of similar high-end banjo bolts on the market!

Torque to 12-14 lbs/ft!