Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.
A couple of things we noticed while testing the Splitstream fuel filters over the past few months.
We were concerned that the filter might slow down the filling process, but we did not experience that with any of our fuel jugs.If you do begin to experience reduced fill speed, then it's probably time to pull the filter out and give it a good wash with hot water and dish soap in the kitchen sink. Be sure to rinse thoroughly!
On the first fill-up, it seems like the sock filter will prevent you from being able to see the fuel level as the tank is filling, but it is just like normal, you can see the fuel level in the sock as the tank fills. Below are links to recent posts on Thumpertalk.com that go into the severity of the problem in much more detail.
Here are some helpful links regarding the fuel system on modern injected bikes:
With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.
Initially, the complete fuel pump assembly had to be replaced at over $300on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......
The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.
With the Gripper Mount, there’s no need to buy a different camera clamp for each helmet or vehicle or use bulky mounting hardware and sticky mounts that leave residue on your equipment. The Gripper Mount is compatible with all GoPro models and serves many purposes throughout your adventures. Use it as a quick-attach fixed camera mount, a handheld stabilizer, or a mini tripod. You can easily unmount and move the Gripper Mount as many times as it takes to find the best perspective. Then simply use the quick-adjust camera mount with 2-axis rotation to line up the perfect angle to capture your action shot!
Dango Designs Gripper Mount Features:
Gripper jaws clamp to irregular shapes and slippery surfaces, such as your helmet, handlebars, or your vehicle.
Slim yet durable construction allows the Gripper Mount to slip effortlessly into tight situations.
Easily movable and serves as a quick-attach fixed mount, handheld stabilizer, or mini tripod.
Flexible front web conforms to your object.
Robust dual torsion spring provides strong clamping force.
2-axis rotation for flexible and quick adjustment to reposition your camera for that perfect shot.
Compatible with ¼ in 20 mounted digital action cameras (adapter version only see tab) (see adapter kit in 2nd tab) and all GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session, and Hero 6 Black.
Mount for all Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
All hardware included.
Here's an independent review of the Dango Gripper mount for GoPro by the popularYouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is. You can check out more of Daniels work at his YouTube channel here:ReturnOfDeeO
Accessory Adapter Kit sold separately for $7.99 as described below: (recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation)
Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine-tune your camera’s position with the 20mm and 35mm extension arms. Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.
Add On Accessory Adapter Kit Features
Compatible with Dango Design Gripper Mount and other action camera mounts
All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
All hardware included
Hardware Included in add on accessory adapter kit*
Pair of MOTO STUFF Icon Decals 3 inches long and 2 inches tall (80mm X 50mm) MOTO STUFF ICON stickers are made by the crew over at Throttle Jockey. Our rectangular version is approximately 3 inches long and 2 inches tall (80mm X 50mm) These are popular for use on fork guards, brake disc covers, fenders, side plates, helmets, tool boxes etc.
Eagle Grit's industrial-strength hand cleaner starts with their micro-scrubbing formulas, created from scratch through their very own recipes. Then mass-produced in their warehouse, each batch is sent over to their distribution center in drums where each bottle is hand-pumped, labeled and packed. Case by case, day by day, truck by truck, Eagle Grit's passion-filled product makes its way down the roads like veins to the heart of the land.
Detergent based formula - no solvents or pumice.
Drain friendly product and recyclable container!
Removes virtually all substances, kills odor, moisturizes and repairs all without irritation.
Lightweight Billet Aluminum Banjo Bolts for Brembo Calipers (pair)
Pair of Billet Aluminum Banjo Bolts with Safety Wire holes (a new set of copper seals included with each kit)
M10 X 1.0 fits all KTM, HUSKY and Gas Gas bikes with Brembo brakes. 19 mm long from the base of the bolt flange to the tip of the threads Sold by the pair (1 pair is 2 bolts), so please be sure to select the quantity you want in the shopping cart before checking out! Our new design fits all KTM, HUSKY and Gas Gas bikes with Brembo brakes and features a small 12mm head so there are no clearance issues at the rear master cylinder! And they are also now drilled for safety wire. At only $18 each, these are half the price of similar high-end banjo bolts on the market!