Husky

Trick Lightweight drilled WORKS style aluminum washers available in 25mm OD and and 18mm OD for use with M6 bolts.

• M25 is 25mm (about 1") OD and is the size shown in the pictures.
• M18 is 18mm OD (about 5/8") and is commonly used on 2 strokes for pipe mounts etc.

Most popular application is on the upper and lower radiator mounts and on the gas tank mounting bolt as shown in the above images.

SOLD individually so please order accordingly!

Pro Pegs Titanium Rear Brake Lever Tip

Get a Grip!

Upgrade your slippery stamped steel stock tip with this super-grippy full titanium tip and eliminate the risk of brake lost at the most inopportune times!

Fits:

• 2016-2020 KTM 125,150, 250 SX
• 2016-2020 KTM 250/350/450 SX-F/XCF
• 2016-2020 Husqvarna TC 125, TC250, FC 250/350/450

Trick looking and lightweight 7071 billet aluminum flange nuts in 4 colors.

Popular for use as brake clevis lock nut, chain guide, and chain roller mounts or any location where you want a trick custom detail!

M6 X 1.0

Available in BLUE, RED and PURPLE

" 8-1/2" X 11" sheet includes 20 premium graphics grade material decals (pressure washer proof). Use them on your fork guards, disc guards, fender arches, air box, shrouds, helmet, swing-arm etc.

Splitstream Fuel Filter HUSQVARNA & KTM

Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.

A couple of things we noticed while testing the Splitstream fuel filters over the past few months.

1. We were concerned that the filter might slow down the filling process, but we did not experience that with any of our fuel jugs. If you do begin to experience reduced fill speed, then it's probably time to pull the filter out and give it a good wash with hot water and dish soap in the kitchen sink. Be sure to rinse thoroughly!
2. On the first fill-up, it seems like the sock filter will prevent you from being able to see the fuel level as the tank is filling, but it is just like normal, you can see the fuel level in the sock as the tank fills. Below are links to recent posts on Thumpertalk.com that go into the severity of the problem in much more detail.

Here are some helpful links regarding the fuel system on modern injected bikes:

• http://www.thumpertalk.com/topic/751249-efi-owners-bike-bogging-the-fix-with-pics/
• http://www.thumpertalk.com/topic/713577-09-crf-450-fuel-problems/
• http://www.thumpertalk.com/topic/676526-09-fuel-pump/

With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.

Initially, the complete fuel pump assembly had to be replaced at over $300 on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......

The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.

Available for the following HUSQVARNA & KTM models:

• HUSQVARNA 2014-2020 TC & FC models
• HUSQVARNA 2014-2020 Enduro FE 250/350/450
• KTM 1/4 Turn cap and 2009-2012 3-tab 1/4 Turn caps
• KTM 2012 Dungey Replica with screw-in cap
• KTM 2013-2020 SXF Models with screw-in cap

The Splitstream radiator cap increases the boiling point of the coolant in your bike's radiator by increasing the cooling system operating pressure.

The stock radiator cap releases coolant at 1.1 BAR (15 psi) of coolant system pressure.

The Splitstream radiator cap is available in

• 1.6 BAR ( 23 psi)
• 1.8 BAR (26 psi)
• 2.0 BAR (30psi)

Use the 1.6 BAR / 23 psi cap to raise the boiling point on most models, especially helpful if you are running aggressively advanced ignition programs, a high compression piston or aggressive cam.

The 1.8 & 2.0 Bar caps are for bikes running HD radiators as the stock radiators are not quite strong enough to operate at sustain high-pressure levels.

MOTO STUFF 280mm Blade Braking System for HUSQVARNA 

Kit Includes:

• MOTO STUFF 280mm Rotor
• MOTO STUFF "Superlight" Billet Mounting bracket. (Hard Anodized Clear for a cool Ti Gray color)

Why upgrade your brakes? You can easily lock them up and slide/skid now, right? That's the problem. Modern motocross bikes have very powerful brakes, however, they don't offer much in the way of modulation or linear application. That is the ability to achieve maximum braking force without wheel lock-up. As soon as the wheel locks up, you lose control or much worse! Power without control is why 4 strokes hook up and outperform 2 strokes. Your ability to modulate (control) the braking force is what makes for a great brake that you can put to maximum use. MOTO STUFF Blade^tm brakes are the highest quality and absolute best performing brakes you can buy.

Team HONDA and the GEICO Factory Connection team have been winning titles with MOTO STUFF Blade^tm Brakes for several years. They can run any brakes they want and they choose the MOTO STUFF Blade System as it provides ultimate performance and significantly improved durability, heat rejection and lasts 2-3 times longer than the competition. Wide modulation range, linear and consistent performance rapidly builds your trust in your brakes at the limit. Below are the main benefits you’ll enjoy with a MOTO STUFF BLADE SYSTEM that will improve your competitive edge!

BENEFITS:

• 36% increase in swept area and 18% increase in moment arm for dramatic improvement in braking power, control and modulation. (AKA The ability to develop maximum stopping power without locking up the brakes)

• Trick lightweight design of the Moto Stuff Blade System weighs only 544 grams (19.2 oz) and looks like nothing else on the market. Nearly a full pound lighter than popular floating designs. The Blade system is 40% lighter than any other 280mm system. That is huge! Title winning teams spend thousands of dollars on Titanium axles and fasteners to shed 8-10 oz's off the front suspension. This is also unsprung and rotating weight, every pound of reduced unsprung weight is the equivalent of 3 pounds savings of sprung weight off the chassis. Reducing rotational mass also has a noticeable positive effect on turn-in and overall handling.
  

• 280mm rotor laser cut and machined in heat-treated 400 series stainless steel for warp-free performance and superior heat dissipation. Moto Stuff Blades typically last 2-3 times longer than the competition!

• Hi-strength 6061 billet aluminum bracket is hard anodized for a tough long-lasting finish. Rotor material is compatible with all top-quality aftermarket pads, we recommend stock pads or our AP Racing Pads for best performance.

• Easily installed in under 30 minutes with common hand tools

• 1-year warranty against defects in material or workmanship

 

Fits All HUSQVARNA Models 125-525 2014-2020

Titanium Rear Brake pedal bolt and nut 

Fits All KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes. 2016-2020 (replaces OEM Part # 0032100406S & 0032100356S)

Fits all HUSQVARNA TC 125/250 / FC 250/450 2014-2020

Set of 6 Ti Fork Guard Bolts for All  KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes (set of 6 replaces OEM part 59001092050)

Fits HUSQVARNA TC 125/250 / FC 250/450 2014-2020

Titanium Front sprocket Bolts for All KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes. 2016-2020 (Replaces OEM part #59033034044)

Fits HUSQVARNA TC 125, 250 & FC 250/450 2014-2020

Motostuff 5" Jersey Logo Heat Transfers. (sold as pair)

Motostuff iron-on logos made from quality MX grade material to resist peeling and fading. Conveniently sized to place anywhere on your jersey.

Application is quick and easy!

Iron-On Application Instructions:

• Medium Temp 265 F / 130 C.
• Simply apply medium pressure for 20 seconds and peel warm.

Titanium Radiator Flange bolt Set for All 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes (set of 4 replaces OEM 0024060123)

Fits HUSQVARNA TC 125/250 / FC 250/450 2016-2020 

New Motostuff decals - Sold individually

4.5" available in:

• red/white
• white/black
• fluorescent /black
• black/fluorescent

Standard decal material - Great for the toolbox, helmet, truck or locations that don't take direct MOTO blast

• M6 X 1.0  bolts have 8mm heads (standard, not fine thread)
• M8 X 1.25 bolts have 10mm head (standard, not fine thread)

Torque to the OEM fastener spec for the bolt being replaced.

Titanium Grade 5 (Ti 6Al-4V) Known as the “workhorse” of titanium alloys, Ti 6Al-4V, or Grade 5 titanium, is 2x stronger than titanium grade 2. This alloy offers high strength and lightweight (half the weight of the stock steel fasteners), high corrosion resistance. Ti 6AI-4V finds many uses in the aerospace and motorsports.

Pair of Moto Stuff rectangular decals 5 inches long and an inch tall (130mm X 25mm)

MOTO STUFF rectangular stickers are made by the crew over at Throttle Jockey.

Our rectangular version is approximately 5 inches long and an inch tall (130mm X 25mm)

These are popular for use on fork guards, brake disc covers, fenders, side plates, helmets, toolboxes, etc.

Only $4.95 / Pair!

Titanium Front Axle and Steering Stem Cap set fits all All 2008-2020 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes (Set of 2 Replaces OEM 70009082000)

Fits HUSQVARNA TC 125/250 / FC 250/450 2014-2020

New Motostuff decal.

Sold individually.

Printed on Premium Grade MX material.

Great for use on a disc guard, fork guards or swing arm.

Get a MOTO STUFF VINTAGE T and get with the program!

Super plush combed cotton is comfy, wrinkle free, pre shrunk and breathes well.

Titanium Motor Mount Bolt Set - KTM & HUSQVARNA

Kit includes:

• 1-Titanium upper front Motor Mount Bolt
• 1-Titanium lower Motor Mount Bolt

Choose between the following two options:

Option #1 Fits: (Pair Replaces OEM part # 77203014000)

• KTM 125/250 2016-2020
  
• KTM 250/350 2013-2020 
• HUSQVARNA TC 125/250 2017 > 
  
• HUSQVARNA FC 250/350 2014-2020
  

Option #2 Fits: (Pair Replaces OEM part # 59003013000)

• KTM 450 2007-2020 
• HUSQVARNA FC 450 2014-2020

oil fill plug for All KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes ( QTY 1 replaces OEM Part 794300020033)

Fits HUSQVARNA TC 125/250 / FC 250/450 2015-2020

With the Gripper Mount, there’s no need to buy a different camera clamp for each helmet or vehicle or use bulky mounting hardware and sticky mounts that leave residue on your equipment. The Gripper Mount is compatible with all GoPro models and serves many purposes throughout your adventures. Use it as a quick-attach fixed camera mount, a handheld stabilizer, or a mini tripod. You can easily unmount and move the Gripper Mount as many times as it takes to find the best perspective. Then simply use the quick-adjust camera mount with 2-axis rotation to line up the perfect angle to capture your action shot!

Dango Designs Gripper Mount Features:

• Gripper jaws clamp to irregular shapes and slippery surfaces, such as your helmet, handlebars, or your vehicle.
• Slim yet durable construction allows the Gripper Mount to slip effortlessly into tight situations.
• Easily movable and serves as a quick-attach fixed mount, handheld stabilizer, or mini tripod.
• Flexible front web conforms to your object.
• Robust dual torsion spring provides strong clamping force.
•  2-axis rotation for flexible and quick adjustment to reposition your camera for that perfect shot.
• Compatible with ¼ in 20 mounted digital action cameras (adapter version only see tab) (see adapter kit in 2nd tab) and all GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session, and Hero 6 Black.
• Mount for all Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included.

Here's an independent review of the Dango Gripper mount for GoPro by the popular YouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is.  You can check out more of Daniels work at his YouTube channel here: ReturnOfDeeO

 

Accessory Adapter Kit sold separately for $7.99 as described below: (recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation) 

Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine-tune your camera’s position with the 20mm and 35mm extension arms.  Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.

Add On Accessory Adapter Kit Features

• Compatible with Dango Design Gripper Mount and other action camera mounts
  • All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
• Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
• The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included

Hardware Included in add on accessory adapter kit*

• 20 mm Universal Extension Arm with Screw
• 35 mm Universal Extension Arm with Screw
• 1/4”-20 Universal Camera Adapter
• * Gripper Mount and GoPro camera not included

 

 

Pair of MOTO STUFF Icon Decals 3 inches long and 2 inches tall (80mm X 50mm)
MOTO STUFF ICON stickers are made by the crew over at Throttle Jockey. Our rectangular version is approximately 3 inches long and 2 inches tall (80mm X 50mm)
These are popular for use on fork guards, brake disc covers, fenders, side plates, helmets, tool boxes etc.

Only $4.95 / Pair!

 

• M6 X 1.0  bolts have 8mm heads (standard, not fine thread)
• M8 X 1.25 bolts have 10mm head (standard, not fine thread)

Torque to the OEM fastener spec for the bolt being replaced.

Titanium Grade 5 (Ti 6Al-4V) Known as the “workhorse” of titanium alloys, Ti 6Al-4V, or Grade 5 titanium, is 2x stronger than titanium grade 2. This alloy offers high strength and lightweight (half the weight of the stock steel fasteners), high corrosion resistance. Ti 6AI-4V finds many uses in the aerospace and motorsports.

New Motostuff Fender Arch decals

• 250mm / 10" long
• Available in White, Black & Gray
• Sold in Pairs
• Premium graphics grade material decals (pressure washer proof)

Pair of chain adjuster bolts/nuts for

Fits:

• All KTM 125/250/300 2-Strokes
• All KTM 250/350/450/525 4-strokes (Set of 2 replaces OEM Part 50304040100)
• All HUSQVARNA TC 125/250
• HUSQVARNA FC 250/450 2014-2020