Moto Stuff M6 Billet Aluminum Flange Nuts
MS-M6FN-RRegular price $4.50 Save $-4.50
Trick looking and lightweight 7071 billet aluminum flange nuts in 2 colors.
Purple and Teal have sold out and no longer available
Popular for use as brake clevis lock nut, chain guide, and chain roller mounts or any location where you want a trick custom detail!
M6 X 1.0
Available in BLUE, RED (Purple and Teal no longer available)
MOTO STUFF lightweight drilled Aluminum Washers
M6AW.25-ALMRegular price $1.80 Save $-1.80
Trick Lightweight drilled WORKS style aluminum washers available in 25mm OD and and 18mm OD for use with M6 bolts.
Most popular application is on the upper and lower radiator mounts and on the gas tank mounting bolt as shown in the above images.
SOLD individually so please order accordingly!
Lightweight Billet Aluminum Banjo Bolts for NISSIN Calipers (pair)
MS-BB-BRegular price $36.00 Save $-36.00
Pair of Billet Aluminum Banjo Bolts with Safety Wire holes (a new set of copper seals included with each kit)
M10 X 1.25 fits all Japanese MX bikes. (does not fit KTM/HUSKY) 20mm long from the base of the bolt flange to the tip of the threads Sold by the pair (1 pair is 2 bolts), so please be sure to select the quantity you want in the shopping cart before checking out! Our new design fits all JAPANESE MX bikes 2004-2020 and features a small 12mm head so there are no clearance issues at the rear master cylinder! And they are also now drilled for safety wire. At only $18 each, these are half the price of similar high-end banjo bolts on the market!
Torque to 12-14 lbs/ft!
Splitstream High Pressure Radiator Caps
SRC-16-18-02Regular price $28.95 Save $-28.95
The Splitstream radiator cap increases the boiling point of the coolant in your bike's radiator by increasing the cooling system operating pressure.
The stock radiator cap releases coolant at 1.1 BAR (15 psi) of coolant system pressure.
The Splitstream radiator cap is available in
Use the 1.6 BAR / 23 psi cap to raise the boiling point on most models, especially helpful if you are running aggressively advanced ignition programs, a high compression piston or aggressive cam.
The 1.8 & 2.0 Bar caps are for bikes running HD radiators as the stock radiators are not quite strong enough to operate at sustain high-pressure levels.
Splitstream Billet Aluminum Radiator Purge Plug - CRF/KXF
SHRP/CRF/KXFRegular price $22.00 Sale price $20.00 Save $2.00
Honda introduced a plastic radiator plug on the left radiator of the 2014 CRF 250R and the 2013-20140 CRF 450R to allow air to be purged from the cooling system when refilling. The plug can be damaged by rock impact or melt under extreme load conditions. Coolant loss or even minimal cooling system pressure loss can lead to rapid serious engine damage with costly repairs. HONDA does not sell the stock plug separate from the radiator!
Kawasaki introduced a plastic radiator plug on the left radiator of the 2016 KX 450F to allow air to be purged from the cooling system when refilling. The plug can be damaged by rock impact or melt under extreme load conditions. Coolant loss or even minimal cooling system pressure loss can lead to rapid serious engine damage with costly repairs.
Splitstream Fuel Filter Kawasaki KX-F
SFFSKXFRegular price $29.95 Save $-29.95
Splitstream Fuel Filter Kawasaki KX-F
Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.
A couple of things we noticed while testing the Splitstream fuel filters over the past few months.
Here are some helpful links regarding the fuel system on modern injected bikes:
With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.
Initially, the complete fuel pump assembly had to be replaced at over $300 on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......
The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.
This filter fits the following Bikes:
Billet Red Banjo Bolts - No Logo (Pair)
MS-RBBRegular price $32.00 Sale price $24.00 Save $8.00
DANGO Designs Gripper Mount for GoPro
DD-GM-OR/BKRegular price $49.95 Save $-49.95
With the Gripper Mount, there’s no need to buy a different camera clamp for each helmet or vehicle or use bulky mounting hardware and sticky mounts that leave residue on your equipment. The Gripper Mount is compatible with all GoPro models and serves many purposes throughout your adventures. Use it as a quick-attach fixed camera mount, a handheld stabilizer, or a mini tripod. You can easily unmount and move the Gripper Mount as many times as it takes to find the best perspective. Then simply use the quick-adjust camera mount with 2-axis rotation to line up the perfect angle to capture your action shot!
Dango Designs Gripper Mount Features:
Here's an independent review of the Dango Gripper mount for GoPro by the popular YouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is. You can check out more of Daniels work at his YouTube channel here: ReturnOfDeeO
Accessory Adapter Kit sold separately for $7.99 as described below: (recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation)
Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine-tune your camera’s position with the 20mm and 35mm extension arms. Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.
Add On Accessory Adapter Kit Features
Hardware Included in add on accessory adapter kit*
Eagle Grit Hand Cleaner - 12 ounces
NB16Regular price $8.95 Save $-8.95