KTM

Pro Pegs Ti pegs weigh only 175 grams each. (5.9 oz). About half the weight of the stock steel pegs with almost twice as much support and grip!

Fits:

• KTM All Models: 125-525 2004-2015 (and 2016 250 2-stroke)
  
• KTM All Models: 125-525 2016-2022
• KTM Enduros: 50 2004-2020, 65 2004-2018, 85 2004-2017
• KTM 2018-20 SX 85 (except 2016 250 2-stroke)
  

• M6 X 1.0  bolts have 8mm heads (standard, not fine thread)
• M8 X 1.25 bolts have 10mm head (standard, not fine thread)

Torque to the OEM fastener spec for the bolt being replaced.

Titanium Grade 5 (Ti 6Al-4V) Known as the “workhorse” of titanium alloys, Ti 6Al-4V, or Grade 5 titanium, is 2x stronger than titanium grade 2. This alloy offers high strength and lightweight (half the weight of the stock steel fasteners), high corrosion resistance. Ti 6AI-4V finds many uses in the aerospace and motorsports.

Pro Pegs Titanium Rear Brake Lever Tip

Get a Grip!

Upgrade your slippery stamped steel stock tip with this super-grippy full titanium tip and eliminate the risk of brake lost at the most inopportune times!

• 2016-2023 KTM 125,150, 250 SX
• 2016-2023 KTM 250/350/450 SX-F/XCF
• 2016-2023 Husqvarna TC 125, TC250, FC 250/350/450

• M6 X 1.0  bolts have 8mm heads (standard, not fine thread)
• M8 X 1.25 bolts have 10mm head (standard, not fine thread)

Torque to the OEM fastener spec for the bolt being replaced.

Titanium Grade 5 (Ti 6Al-4V) Known as the “workhorse” of titanium alloys, Ti 6Al-4V, or Grade 5 titanium, is 2x stronger than titanium grade 2. This alloy offers high strength and lightweight (half the weight of the stock steel fasteners), high corrosion resistance. Ti 6AI-4V finds many uses in the aerospace and motorsports.

Splitstream Fuel Filter HUSQVARNA & KTM

Each Splitstream fuel filter is made of fuel safe nylon mesh for long life and protection. Designed for a snug fit under the fuel cap, where it strains all fuel that enters the fuel tank. When you are riding it is under your fuel cap ready for the next fill up.

A couple of things we noticed while testing the Splitstream fuel filters over the past few months.

1. We were concerned that the filter might slow down the filling process, but we did not experience that with any of our fuel jugs. If you do begin to experience reduced fill speed, then it's probably time to pull the filter out and give it a good wash with hot water and dish soap in the kitchen sink. Be sure to rinse thoroughly!
2. On the first fill-up, it seems like the sock filter will prevent you from being able to see the fuel level as the tank is filling, but it is just like normal, you can see the fuel level in the sock as the tank fills. Below are links to recent posts on Thumpertalk.com that go into the severity of the problem in much more detail.

Here are some helpful links regarding the fuel system on modern injected bikes:

• http://www.thumpertalk.com/topic/751249-efi-owners-bike-bogging-the-fix-with-pics/
• http://www.thumpertalk.com/topic/713577-09-crf-450-fuel-problems/
• http://www.thumpertalk.com/topic/676526-09-fuel-pump/

With the introduction of fuel injection on several 2009 MX bikes, clean fuel has become critical. Many owners are experiencing loss of power and starting issues related to contaminated fuel. The contaminants gradually accumulate in the in-tank filter and over time reduce flow to the point that it begins to affect performance.

Initially, the complete fuel pump assembly had to be replaced at over $300 on some models. The quality control on pump gas is really poor nowadays and you will not believe what you'll find in the filter! Over a short period of time, unfiltered fuel allows debris that will eventually begin to cause starting problems and bogging due to clogging. In severe cases, the bike will not start/run at all and can cause the bike to bog or stall at the most inopportune of times.......

The fine micron mesh material used in the Splitstream fuel filter will even filter out water, however, you will need to pull the filter and shake it out after fueling, otherwise, the vibration of the running bike will allow the water to pass through the filter.

Available for the following HUSQVARNA & KTM models:

• HUSQVARNA 2014-2020 TC & FC models
• HUSQVARNA 2014-2020 Enduro FE 250/350/450
• KTM 1/4 Turn cap and 2009-2012 3-tab 1/4 Turn caps
• KTM 2012 Dungey Replica with screw-in cap
• KTM 2013-2020 SXF Models with screw-in cap

Pro Pegs Ti pegs weigh only 175 grams each. (5.9 oz). About half the weight of the stock steel pegs with almost twice as much support and grip!

Fits:

• KTM All 125-525 2016-2022 and 2018-19 SX 85 (except 2016 250 2 stroke)
• KTM All Models 125-525 2004-'15 (and 2016 250 2 stroke)
• KTM Enduros, 50 2004-2020, 65 2004-'18, 85 2004-'17

Set of 4 Ti  Subframe Bolts for 2016-2022 125 SX 250SX and 250SXF, 350 SXF, and 450 SXF  (Set of 4 replaces OEM part 0019080206S & 79003003000)

Does not fit HUSQVARNA

Titanium Motor Mount Bolt Set - KTM, GASGAS & HUSQVARNA

Kit includes:

• 1-Titanium upper front Motor Mount Bolt
• 1-Titanium lower Motor Mount Bolt

Choose between the following two options:

• KTM 125/250 2016-2024
  
• KTM 250/350 2013-2024 
• GASGAS MC250F 2021-2024
• HUSQVARNA TC 125/250 2014-2024  
  
• HUSQVARNA FC 250/350 2014-2024
  

Option #2 TIEB45KTM Fits: (Pair Replaces OEM part # 59003013000)

• KTM 450 2007-2024
• GASGAS MC450F 2024
• HUSQVARNA FC 450 2014-2024
• HUSQVARNA TC 125-250 2024 

Titanium Rear Brake pedal bolt and nut 

Available for:

All KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes. 2016-2022 (replaces OEM Part # 0032100406S & 0032100356S)

 All HUSQVARNA TC 125/250 / FC 250/450 2014-2022

And 2023 FC250/450

Titanium Screw Plastic 

Body fastener kit

6 bolts to fit the fork guard brake line clamp bracket, rear mud flap and upper front shroud to tank locations. 

For All KTM 125, 250, 300 2 stroke and all 250, 350, 450, and 525 four strokes. 2016-2020

Fits HUSQVARNA TC 125, 250 & FC 250/450 2014-2020

Set of 6 Ti Fork Guard Bolts for All  KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes (set of 6 replaces OEM part 59001092050)

Fits HUSQVARNA TC 125/250 / FC 250/450 2014-2020

Titanium Radiator Flange bolt Set for All 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes (set of 4 replaces OEM 0024060123)

Fits HUSQVARNA TC 125/250 / FC 250/450 2016-2020 

Titanium Front End Fastener Kit

 Front End Kits include: 8-Triple Clamp bolts, 4-handlebar clamp bolts, 4-fork lug pinch bolts and 2-brake caliper mounting bolts.

(Please note if you have a Factory Edition or Rockstar Edition or aftermarket clamps, please measure a bolt and let us know so we can exchange them for the correct size)

Titanium Grade 5 (Ti 6Al-4V) Known as the “workhorse” of titanium alloys, Ti 6Al-4V, or Grade 5 titanium, is 2x stronger than titanium grade 2. This alloy offers high strength and lightweight (half the weight of the stock steel fasteners), high corrosion resistance. Ti 6AI-4V finds many uses in the aerospace and motorsports.

Install to the OEM torque specifications

Titanium Engine Fastener / Bolt Kits And Front End Kits

Engine Kits include: Right and left engine case bolts, ignition cover bolts, clutch cover bolts, water pump cover, starter, chain guard, etc. Each component set of bolts is packaged in a ziplock with qty, length and location information.

Titanium Grade 5 (Ti 6Al-4V) Known as the “workhorse” of titanium alloys, Ti 6Al-4V, or Grade 5 titanium, is 2x stronger than titanium grade 2. This alloy offers high strength and lightweight (half the weight of the stock steel fasteners), high corrosion resistance. Ti 6AI-4V finds many uses in the aerospace and motorsports.

Install to the OEM torque specifications

Long Titanium Seat Bolt for All KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes.

2016-2022 Replaces OEM part #79107040010

With the Gripper Mount, there’s no need to buy a different camera clamp for each helmet or vehicle or use bulky mounting hardware and sticky mounts that leave residue on your equipment. The Gripper Mount is compatible with all GoPro models and serves many purposes throughout your adventures. Use it as a quick-attach fixed camera mount, a handheld stabilizer, or a mini tripod. You can easily unmount and move the Gripper Mount as many times as it takes to find the best perspective. Then simply use the quick-adjust camera mount with 2-axis rotation to line up the perfect angle to capture your action shot!

Dango Designs Gripper Mount Features:

• Gripper jaws clamp to irregular shapes and slippery surfaces, such as your helmet, handlebars, or your vehicle.
• Slim yet durable construction allows the Gripper Mount to slip effortlessly into tight situations.
• Easily movable and serves as a quick-attach fixed mount, handheld stabilizer, or mini tripod.
• Flexible front web conforms to your object.
• Robust dual torsion spring provides strong clamping force.
•  2-axis rotation for flexible and quick adjustment to reposition your camera for that perfect shot.
• Compatible with ¼ in 20 mounted digital action cameras (adapter version only see tab) (see adapter kit in 2nd tab) and all GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session, and Hero 6 Black.
• Mount for all Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included.

Here's an independent review of the Dango Gripper mount for GoPro by the popular YouTube Moto Vlogger Daniel Olszewski. He addresses the concerns we had when we first saw one of the mounts and does a really nice job of showing how versatile the Dango Gripper is.  You can check out more of Daniels work at his YouTube channel here: ReturnOfDeeO

Accessory Adapter Kit sold separately for $7.99 as described below: (recommended for use on most modern MOTO helmets to position the camera far enough away from the chin guard to allow for proper angle adjustment. See Daniels video below for a clear explanation) 

Increase your camera angle and mounting options with our new adapter pack for the multisport Gripper Mount from Dango Design! The Adapter Pack makes the Gripper Mount even more flexible. Fine-tune your camera’s position with the 20mm and 35mm extension arms.  Make your Gripper Mount compatible with digital action cameras using the ¼” – 20 adapter.

Add On Accessory Adapter Kit Features

• Compatible with Dango Design Gripper Mount and other action camera mounts
  • All GoPro® camera models: Hero2, Hero3, Hero4, Hero5, Hero5 Black, Hero5 Session, Hero Session and GoPro Hero 6 Black
• Makes the Dango Design Gripper Mount Compatible with ¼ in 20 mounted digital action cameras
• The Gripper Mount works for Powersports and action sports, including ATVs, motorcycles, bicycles, snowboarding, skiing, surfing, kayaking, motocross, and more!
• All hardware included

Hardware Included in add on accessory adapter kit*

• 20 mm Universal Extension Arm with Screw
• 35 mm Universal Extension Arm with Screw
• 1/4”-20 Universal Camera Adapter
• * Gripper Mount and GoPro camera not included

Titanium Front Axle and Steering Stem Cap set fits all All 2008-2020 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes (Set of 2 Replaces OEM 70009082000)

Fits HUSQVARNA TC 125/250 / FC 250/450 2014-2020

Oil fill plug for All KTM 125, 250, 300 2 stroke and all 250, 350, 450 and 525 four strokes ( QTY 1 replaces OEM Part 794300020033)

Fits

• HUSQVARNA TC 125/250 / FC 250/450 2015-2020
• KTM SX/SXF/EXC 125-450 All years

Does not fit Factory or Rockstar Editions or HINSON Clutch Covers

Titanium Valve Cover Bolt Set - KTM & HUSQVARNA

Choose your bike year/model below:

Option #1: 

• KTM SXF 250/350 (Set of 3 bolts replaces OEM 77336054150)
  
• HUSQVARNA FC 250/350 2014-2022
  

Option #2: 

• KTM 450 2013-2018 (set of 4 replaces OEM part#78036054100)
• HUSQVARNA FC 450 2014-2018 

Option #3: 

• KTM 450 2019-2022 (set of 3 bolts replaces OEM part # 79136054000)
• HUSQVARNA FC 450 2019-2022

Option #4: 

• 2023 KTM Factory Edition 450 

Pair of chain adjuster bolts/nuts for

Fits:

• All KTM 125/250/300 2-Strokes
• All KTM 250/350/450/525 4-strokes (Set of 2 replaces OEM Part 50304040100)
• All HUSQVARNA TC 125/250
• HUSQVARNA FC 250/450 2014-2020